Califone Portable Speaker PA916 User Manual

PowerPro 916  
Portable  
Public Address  
Systems  
Owner’s  
Manual  
PA916 Public Address Speaker  
PA916-PS Powered Companion PA  
PA916-SP Passive Companion Speaker  
 
Telescoping Handle  
1
Two 16-channel UHF wireless mic receivers  
Compact Disc Player  
2
3
Power Pro 916  
Variable Speed Cassette Recorder/Player  
Microphone Volume (2)  
Speech/Music Switch (2)  
XLR & 1/4Microphone Inputs(2)  
Audio Line Out Volume  
Audio Line Out XLR (2)  
4
S P E C I F I C A T I O N S  
5
6
7
1
8
9
CD-Tape On/Off & Volume  
Line-In Volume Control  
Line-In RCA Jacks  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
2
28  
Line-Out RCA Jacks  
Treble Control  
3
4
Bass Control  
8
5
Digital Master Volume  
16-channel UHF Transmitter  
5 Ampere Fuse  
10  
14  
15  
6
7
9
A/C Power Socket  
Battery Low/Charge Indicators  
Green Power On Indicator  
Power On/Off Switch  
16  
11  
12  
13  
Voice Priority (Ducking) Switch  
1/4Phone Jack Speaker Out  
1/4Phone Jack Speaker Out Switched  
Speaker Mute Switch  
18 19 20 21  
17  
22 23  
27  
Beefy 3.5Integral Wheels  
LED Lights for Power, RF, Audio  
24 25 26  
2
 
Operation  
Battery  
Charge the battery for at least 10 hours before using the PA916 or PA916-PS. Simply plug the power cord into an AC  
outlet and charging begins automatically. The charging indicator will !ash until fully charged, then it will stay green. The  
unit can be used while it is plugged in for charging.  
There are two indicators above the main power switch. When the unit is turned on, the one on the left will light “red”  
when the battery has a low charge. The one on the right will glow “green” if the battery is fully charged or if operating  
on A/C power.  
It is recommended that the battery be recharged after several hours of usage, rather than stored with a low battery. This  
will prolong battery life. Storing more than 30 days without recharging will deteriorate the battery.  
Digital Master Volume Control  
When the main power switch is turned on, the Digital Master Volume Control is at the lowest level to prevent accidental  
damage to the ampli"er or internal speakers. The volume can be controlled in two ways; using the “Up”“Down” buttons  
on the mixer panel or using the RC-300 infrared remote control. The remote sensor must be used in front of the speaker  
as the sensor is behind the speaker grille.  
Recommended Set-up Procedure  
Ideally the master volume should be at maximum volume before the wireless receiver and microphone volumes  
are adjusted to the desired loudness. Since there are always at least two (2) volume controls to contend with, it is  
suggested that prior to turning the power on the UHF receiver volume controls be set at “10 o’clock. Also set the  
microphone volume controls at “10 o’clock. Turn on the main power switch and use either a wireless microphone  
or cabled microphone to adjust the master volume.  
Tape & CD  
The main power switch does not control the CD and Tape recorder. A separate power switch is combined with the  
Tape/CD volume control to limit battery drain when the Tape or CD are not being used.  
Wireless Receivers  
There are two (2) independent combination XLR/1/4” jacks for using microphones with cables. Each jack has a volume  
control which e#ects the loudness of both wired and wireless microphones. Also each has a “Voice/Music” switch. On  
“music” program the sound is full "delity, while on “voice” the sound is tailored to give maximum projection while limit-  
ing battery drain.  
3
 
Operation continued  
Line In  
Insert both RCA plugs into the RCA jacks when using a stereo input. The left and right channels are combined so no pro-  
gram material is lost. If the source is monaural, either RCA jack can be used. The Line In volume control is used to increase  
or decrease the level of the input signal.  
Line Out  
The two RCA jacks are used to connect to the input of another piece of equipment such as a tape recorder, mixer or  
another ampli"ed speaker. The outputs are monaural and volume level will depend on the volume of the source. For  
example, the tape or CD player level is controlled by the tape/CD volume control. Lie out is independent of the Master  
Volume Control.  
Tone Controls  
The separate base and treble controls provide a wide range of adjustment for increasing or decreasing either the bass or  
treble from “!atfrequency response. The center or “12 o’clockposition is !at.  
Speaker Mute Switch  
Engaging this switch will cut o# the sound of all speakers, internal and external, except as explained in the section under  
“PA916-PS operation.  
Voice Priority  
This feature is used for voice override of the music program when using a microphone. The “ducking” circuit attenuates  
the music when a person speaks into the microphone. After a 3 second delay in the speech, the music returns to the  
previous level.  
4
 
Wireless Operation  
Feedback is a shrill screeching sound produced by the speaker system when a microphone is being used too close to the  
front of the speaker. The microphone picks up the sound of the speaker system and it becomes reampli"ed. It is a self-  
sustaining loop which can damage the system if allowed to continue, not to mention the annoyance caused to persons  
nearby. Always stand 4 to 6 feet from the speaker to minimize the opportunity for feedback from the speaker system.  
Wireless UHF Receivers  
Wireless receiver “A” is preset at the factory for channel 4 and  
UHF FULL DIVERSITY  
receiver “B” is set on channel 6. There are three (3) LEDs on the  
receiver; power (green), RF reception (red) and Audio reception  
(amber).  
There are also LEDs on the front of the speaker above the grille  
making it easy to see if the microphone and receiver are work-  
ing properly. A red LED indicates RF (radio frequency) from the  
microphone, while an amber LED indicates audio.  
Wireless Transmitter  
The PowerPro PA916 incorporates a 16 channel UHF transmitter with its own power switch for wireless transmission to  
the Powered Companion Speakers PA916-SP. The transmitter is preset at the factory to channel 13. It is recommended  
that the user not randomly change this setting. If using the transmitter function change wireless receiver “Afrom chan-  
nel 1 to any other channel except channel 13 to prevent the transmitter from blocking the receiver.  
Microphone Lockout  
Two wireless microphones can be used at the same time, but separate channels (frequencies) must be used. For instance,  
if using receiver “A” on channel 4, two microphone beltpack transmitters cannot be used at the same time. The "rst  
transmitter turned on will dominate and lock out the other. The second microphone should be used with receiverBon  
a di#erent frequency which will allow two persons to talk at the same time.  
Turn the transmitter power switch to OFF when not being used to minimize battery drain.  
5
 
Microphones & Belt-Pack Transmitter  
Q-316 Wireless Microphone  
16-Channel UHF Transmitter  
Battery Compartment  
Channel Selector Switch  
Power Low Battery LED  
LM-316 Lapel Mic  
M-316 Wireless Belt Pack Transmitter  
Microphone Jack  
Power On Switch  
CM-316 Collar Mic  
Power On/  
Low Batt. LED  
Volume Control  
16-Channel  
UHF Transmitter  
Battery  
Compartment  
HBM-316 Headband Mic  
6
 
Cassette Recorder/Player  
Note: Remove the protective pad from behind the cassette door before inserting a cassette tape.  
1
2
3
4
5
6
7
RECORD  
Press this key together with either F. PLAY or R.PLAY to Record.  
Press this key to rewind the tape.  
REWIND  
REVERSE PLAY  
STOP  
Press this key to Play the tape backwards.  
Press this key to stop the tape.  
FORWARD PLAY  
FAST FORWARD  
MODE  
Press this key to play the tape forward.  
Press this key for Fast Forward.  
Press this key to select one of the following 3 modes.  
1) The tape will play to the end in either direction and stop automatically.  
2) The tape will play to the end in the forward mode, then reverse and play to the end of the other side of the tape in Record or Play  
3) This mode provides continuous play operation in the Play function.  
8
MODE LED INDICATORS  
SPEED ADJUSTMENT  
COUNTER  
9
12  
11  
10  
10  
11  
12  
COUNTER RESET BUTTON  
EJECT  
9
8
7
Normal speed; center position. Turn  
clockwise to increase the speed in  
3% increments up to 15%. Turn counter  
clockwise to reduce the speed in 3%  
increments down to 15%.  
The counter is a 3-digit LCD display.  
Reset to “000by pushing the button.  
This button opens the cassette door.  
1
2
3
4
5
6
7
 
Automatic Cassette Program Search System  
The APSS (Automatic Program Search System) allows the user to skip the program being played  
and move the tape in the Forward or in the Reverse direction to the next program or to the previous  
program. It operates on the principal that there is a short period of silence between programs.  
When theTape Deck is in the Play mode and the“FF”is momentarily pressed and released within 0.5  
sec, the tape advances rapidly until the next program ahead is reached. At this point, the tape stops  
momentarily and playback of the next program starts.  
When theTape Deck is in the Play mode and the“FR”is momentarily pressed and released within 0.5  
sec, the tape rewinds rapidly until the beginning of the previous program is reached. At this point  
the tape stops momentarily and playback of the previous program starts.  
CD Player  
After the power is turned on the LCD display will read “NO disc” Gently push the CD into the slot and  
the CD will be recognized and begin playing track #1.  
1
2
3
CD SLOT  
LCD DISPLAY  
PAUSE/PLAY  
When “Play” is pressed, the "rst track will begin to Play. When Play is pressed again, the mode goes to  
Pause. When pressed a third time the mode returns to Play.  
1
9
8
4
3
NO dISC  
2
7
10  
6
5
When STOP is pressed from Play or Pause the program is advanced to the end of the last track on the CD.  
4
5
STOP  
SKIP FORWARD  
When FWD is pressed from the Stop mode, the program will advance to the "rst track. When pressed  
from Play or Pause mode, the program will advance one track. Continuing to press FWD will advance  
one track each time.  
8
 
CD PLAYER Continued  
6
SKIP/REVERSE  
When REV is pressed from the Stop mode, the program will go back one track and begin playing  
the last track on the CD. When pressed from Play or Pause mode, the program will go back to the  
beginning of the track which was already playing. Continuing to press REV will step back one  
track at a time.  
7
8
9
REPEAT/ENTER  
SHUFFLE  
Pressing Repeat once will continuously replay the selected track. Pressing it twice will replay all  
tracks continuously. Pressing Repeat a third time will clear the settings.  
Pressing Shu$e from Stop, Play or Pause will result in random selection of tracks and begin  
playing continuously. Pressing Shu$e again will clear the program.  
PROGRAM  
In Stop mode, press Program and observe “P 1: on the LCD. Press FWD and see “1:01, press FWD  
again and see “1 :02. Press enter and “2will appear in the upper right of the LCD. Press FWD three  
more times and see1:05. Press Enter and see5added to the LCD. Press play and the second track  
will play, then advance to track 5. After playing all the selected tracks the program advances to the  
end of the CD. Pressing Play will repeat the program. To clear the program in the Stop mode, just  
press Program. Individual selections can be cleared while they are playing by pressing Program.  
This will not a#ect other selected tracks.  
10  
EJECT  
Pressing Eject from any mode will advance the program to the last track on the CD and eject the  
CD. “NO dISCwill appear on the LCD.  
NOTE: The CD player is capable of playing CD, CD-R and CD-RW discs, however due to the condition of the disc or the original it  
was copied from some discs may not play.  
9
 
Powered Companion Speaker PA916-PS  
The Powered Companion PA has the same ampli"er, power supply and speaker compliment as the full featured PowerPro PA916. It  
does not have the mixer panel because it can be controlled by the PowerPro PA916.  
With the integral 16-channel selectable wireless UHF receiver, it can function as a stand alone PA speaker when using a Q-316  
Handheld microphone or the M-316 Beltpack transmitter with a LM-316, CM-316 or HBM-316 microphone. Although there are 5  
LEDs on the front of the PA916-PS only 3 lights function on this unit because there is only one receiver. The red LED indicates RF,  
the amber LED is for audio, and the green LED indicates power On.  
Full Wireless Operation  
As the transmitter on the PA-16 is preset on channel 13, the receiver of the PA916-PS is also set on 13. Any audio from the PA916  
can be transmitted to the PA916-PS without wiring. There is no limit on the number of PA916-SP speakers that can be used with the  
PA-916 within a range of 300 feet.  
Audio Line Buss  
When linking one or two PA916-PSs to the PowerPro PA916 via audio line, the PSC-50 XLR cable is connected to Audio Line Out XLR  
connector on the PA916. The other end is connected to Line In XLR on the Powered Companion Speaker.  
The Master Volume Control on the Audio Line panel of the master will adjust the PowerPro PA916 as well as all the Powered or Pas-  
sive Companion Speakers, however the loudness needs to be adjusted via the Master Volume Control on the PA916-PS as well.  
Note: The mute switch on the PA916 will silence all speakers connected to it by cable. However in the full wireless mode using the  
transmitter of the PowerPro the mute will have no e#ect.  
10  
 
Power Pro 916-P  
1
Telescoping Handle  
1
16-channel UHF wireless mic receivers  
Audio Line Out XLR  
2
3
Treble Control  
4
Bass Control  
5
Digital Master Volume  
Dual Steel Skid Guards  
A/C Power Socket  
6
3
2
7
4
7
8
5
6
Battery Low/Charge Indicators  
Green Power On Indicator  
Power On/Off Switch  
9
10  
11  
12  
13  
14  
15  
16  
15  
8
9
Voice Priority (Ducking) Switch  
1/4Phone Jack Speaker Out  
1/4Phone Jack Speaker Out Switched  
Speaker Mute Switch  
16  
10  
11  
12  
13  
14  
Integral Wheels  
Power Pro 916-SP  
1
2
3
Telescoping Handle  
1
2
3
1/4Phone Jack Speaker In  
Integral Wheels  
11  
 
Passive Speaker System PA916-PS Operation  
The PA916-SP is connected to one of two outputs from the PowerPro PA916 or Powered Companion Speaker via SP-50 Cable with  
1/4phone plugs.  
Connecting to the “Speaker Outjack will divide the power between the PowerPro PA916 or PA916-PS and PA916-SP. Connecting to  
the “Switched Outwill disconnect the internal speakers of the PA916 and deliver all of the power to the PA916-SP.  
NOTE: There are "ve (5) LEDs on the front of the speaker, however they are disconnected because there is no internal ampli"er or  
wireless receiver in this passive system.  
Mechanical Notations  
Telescoping Handle and Wheels  
These are only intended for pulling the PowerPro over relatively smooth surfaces. Using the handle to lift or carry the unit or pull-  
ing up stairs will cause damage not covered by the warranty.  
Tripod Mount  
A recess is incorporated on the bottom of all PowerPro Speakers for mounting to the TP-50 tripod.  
12  
 
Speci!cations  
Acoustic Speaker Compliment  
Woofer  
10Diameter, 40 Oz. Magnet, 2Dia. Voice Coil, 6 Ohm  
Compression Horn Driver, 12 Oz. Magnet, 1Voice Coil, 8 Ohm  
45Hz to 18KHz  
Tweeter  
Frequency Response  
Ampli!er  
90 Watts RMS @ 5% THD (AC)  
Sound Pressure Level  
Power Sources  
94 dB, 1 Watt @ 1 Meter  
100-240 volt AC switchmode power supply and 12 volt 7 AH  
maintenance-free lead acid batteries (2)  
Wireless System  
Receiver: Two 16-channel selectable UHF diversity wireless receivers 798-805 MHz.  
Antennas are hidden internally.  
Microphone Transmitters  
Handheld wireless microphone or beltpack transmitters optional. Powered by 2 ea. 1.5 volt AA batteries (included). Beltpack trans-  
mitter used with choice of hands-free headset, collar or lapel microphones.  
CD Player  
Built-in anti-shock mechanism. Fully programmable. Shu$e feature. Plays CD, CD-R/RW.  
Tape Cassette  
Full logic player and recorder. Automatic program search feature. 4-digit LCD tape counter. Variable speed. Auto reverse.  
Transmitter to Powered Companion Speaker  
16-Channel selectable UHF transmitter for wireless transmission from PA916 to multiple PA916-SP speakers. 300 ft. range.  
Audio Line  
Line level XLR jacks (2) providing for attaching PA916-SP speakers via cable. Features volume control for remote speaker(s).  
Mixer Panel  
Mixer panel accepts two wired microphones via high quality combination connectors for both XLR and 1/4phone plugs. Voice  
music switch adds emphasis in the voice range for longer range projection. Line-In via dual RCA jacks with volume control.  
Line-Out via dual RCA jacks. Separate Bass and Treble tone controls. Voice priority switch activates “ducking circuitwhich over-  
rides music programs when microphone is used. Speaker mute switch mutes the main speaker plus all other speakers connected.  
Speaker out. Both switched and unswitched 1/4phone jacks for connecting speakers.  
Dimensions  
Weight  
26 H x 12W x 10D  
52 lbs.  
Compliance  
FCC, CE, C-UL  
13  
 
CAUTION  
RISK OF ELECTRIC SHOCK - DO NOT OPEN  
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK.  
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QAULIFIED PERSONNEL.  
The exclamation point within a  
The lightening flash with arrowhead  
triangle is intended to tell the user  
within a triangle is intended to tell  
that important operating and servicing  
the user that parts inside the product  
instructions are in the papers with  
!
are a risk of electric shock to persons.  
the appliance.  
This product is not designed to  
function normally in strong electro-  
magnetic fields. Consequently, the  
Ce produit n’est pas conçu pour  
un fonctionnement dans de forts  
WARNING:  
champs électromagnétiques. Par  
conséquent, la qualité sonore peut  
diminuer si ce produit est exposé  
TO REDUCE THE RISK OF  
FIRE OR ELECTRIC SHOCK, SO  
NOT EXPOSE THIS APPLIANCE  
TO RAIN OR MOISTURE.  
audio quality may degrade while  
the product is exposed to strong electromagnetic  
fields. Normal audio quality operation will be  
recovered when the strong electromagnetic field  
is no longer present.  
à un fort champ életromagnétique. La qualité  
sonore redeviendra normale après affaib-lisse-  
ment du champ électromagnétique.  
IMPORTANT SAFETY INSTRUCTIONS  
POWER CORD PROTECTION - POWER SUPPLY CORDS  
ATTENTION: ALL SAFETY AND OPERATING INSTRUCTIONS  
SHOULD BE READ BEFORE OPERATING APPLIANCE. ALL OPER-  
ATING AND USE INSTRUCTIONS SHOULD BE FOLLOW-  
ED WHEN OPERATING THE APPLIANCE. HEED AND ADHERE  
TO ALL WARNINGS ON THE APPLIANCE AND IN THE OPERATING  
INSTRUCTIONS. RETAIN ALL SAFETY AND OPERATING INSTRUC-  
TIONS FOR FUTURE REFERENCE.  
SHOULD BE ROUTED SO THAT THEY ARE NOT LIKELY TO BE  
WALKED ON OR PINCHED BY ITEMS PLACED UPON OR AGAINST  
THEM, PAYING PARTICULAR ATTENTION TO CORDS  
AT PLUGS, CONVENIENCE RECEPTACLES, AND THE POINT WHERE  
THEY EXIT FROM THE APPLIANCE.  
CLEANING - THE APPLIANCE SHOULD BE CLEANED ONLY AS REC-  
OMMENDED BY THE MANUFACTURER.  
WATER & MOISTURE - DO NOT USE THE APPLIANCE NEAR  
WATER; IE. BATHTUB, WASHBOWL, KITCHEN SINK, LAUNDRY  
TUB, WET BASEMENT OR SWIMMING POOL.  
NON USE PERIODS - UNPLUG THE APPLIANCE POWER CORD  
FROM THE OUTLET WHEN LEFT UNUSED FOR A LONG PERIOD OF  
TIME.  
VENTILATION - DO NOT SITUATE THE APPLIANCE SO THAT  
ITS LOCATION OR POSITION INTERFERES WITH ITS PROPER  
VENTILATION. FOR EXAMPLE, THE APPLIANCE SHOULD NOT  
BE SITUATED ON A BED, SOFA, RUG OR SIMILAR SURFACE THAT  
MAY BLOCK THE VENTILATION OPENINGS. THE  
OBJECT & LIQUID ENTRY - CARE SHOULD BE TAKEN SO THAT  
OBJECTS DO NOT FALL AND LIQUIDS ARE NOT SPILLED INTO THE  
ENCLOSURE THROUGH OPENINGS.  
APPLIANCE SHOULD NOT BE PLACED IN A BUILT-IN  
INSTALLATION, SUCH AS A BOOKCASE OR CABINET, THAT  
MAY IMPEDE THE FLOW OF AIR THROUGH THE VENTILATION  
OPENINGS.  
DAMAGE REQUIRING SERVICE - THE APPLIANCE SHOULD BE SER-  
VICED BY QUALIFIED SERVICE PERSONNEL WHEN: (A) THE POWER  
SUPPLY CORD OR THE PLUG HAS BEEN DAMAGED (B) OBJECTS  
HAVE FALLEN OR LIQUID HAS BEEN SPILLED INTO THE APPLIANCE  
(C) THE APPLIANCE HAS BEEN EXPOSED TO RAIN (D) THE APPLI-  
ANCE DOES NOT APPEAR TO BE OPERATING NORMALLY OR EXHIB-  
ITS A MARKED CHANGE IN PERFORMANCE (E) THE APPLIANCE HAS  
BEEN DROPPED OR THE ENCLOSURE DAMAGED.  
HEAT - SITUATE THE APPLIANCE AWAY FROM HEAT SOURCES  
SUCH AS RADIATORS, HEAT REGISTERS, STOVES OR OTHER AP-  
PLIANCES (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.  
POWER SOURCES - CONNECT THE APPLIANCE ONLY TO A  
POWER SUPPLY TYPE DESCRIBED IN THE OPERATING INSTR-UC-  
TIONS OR MARKED ON THE APPLIANCE.  
SERVICING - THE USER SHOULD NOT ATTEMPT TO  
SERVICE THE APPLIANCE BEYOND THAT DESCRIBED IN  
THE OPERATING INSTRUCTIONS. ALL OTHER SERVICING REFER TO  
A QUALIFIED SERVICE PERSONNEL.  
GROUNDING OR POLARIZATION - PRECAUTIONS SHOULD BE  
TAKEN SO THAT THE GROUNDING OR POLARIZATION MEANS OF  
THE APPLIANCE ARE NOT DEFEATED.  
14  
 
 

Blodgett Oven 966 User Manual
Bosch Appliances Clothes Dryer WTMC5521 User Manual
BreatheAudio Stereo Amplifier BA 200 User Manual
Briggs Stratton Blower 233400 to 233499 User Manual
Briggs Stratton Pressure Washer 020219 User Manual
Cabletron Systems Switch 9T122 24 User Manual
Cannon Webcam CT1 1041 000 User Manual
Canon Printer MP460 User Manual
Canon Printer MX640 User Manual
Chamberlain Home Security System 33LMC User Manual